1OPERATING INSTRUCTIONS AND PARTS LISTINSTRUCCIONES DE OPERACIÓN Y LISTA DE PIEZAS0A7859Copyright © July 11, 2002 DBInc.Printed in U.S.A.MC18Concrete
10 DOWARNING: FAILURE TO COMPLY WITH THESE WARNINGS AND OPERATINGINSTRUCTIONS COULD RESULT IN DEATH OR SERIOUS BODILY INJURY.SAFETY FIRST!WARNINGSDO’s
11SAFETY FIRST!WARNINGSDO’s and DO NOT’sWARNING: FAILURE TO COMPLY WITH THESE WARNINGS AND OPERATINGINSTRUCTIONS COULD RESULT IN DEATH OR SERIOUS BODI
12FIGURE 22A. BLADE SHAFT NUT: Use to tighten the outer flangeagainst the diamond blade.2B. OUTER FLANGE: Use to hold the diamond blade inpositio
13PRE OPERATION CHECKLISTBefore leaving our factory, every machine is thoroughly tested. Follow our instructions strictly andyour machine will give y
14• The Handle must be attached. Place Handlein position and securely tighten Knobs.• Check the engine oil level. Service before using. Referto th
15Always pay extreme care and attention to thepreparation of the machine before starting.Remove all wrenches and tools from the floorand the machine.A
16• Screw Feed Version:Raise the blade out of the cut by pulling up on thedepth control lock and slowly turning the hand wheelclockwise. Raise the bl
17SPECIAL OUTER FLANGE ASSY 1/2" (12.7mm)WIDE CUT (P/N 167963)• A Special Outer Flange Assembly is available as a fieldinstalled accessory. It e
18It is critical that the Governor and throttle on all internalcombustion engines be adjusted properly. The engine speedis preset at the factory for t
19NOTE:NOTA:
2EVERY MACHINE IS THOROUGHLY TESTED BEFORE LEAVING THE FACTORY. EACH MACHINE IS SUPPLIEDWITH A COPY OF THIS MANUAL. OPERATORS OF THIS EQUIPMENT MUST
20Diagram 1 – Frame & Axle
21 Diagram 1 – Frame & Axle (Rev July 11, 2002) BILL OF MATERIAL INDEX P/N DESCRIPTION
22Diagram 2 – Depth Control (Screw Feed)
23 Diagram 2 – Depth Control (Screw Feed) BILL OF MATERIAL INDEX P/N DESCRIPTION
24Diagram 3 – Depth Control (Lock Bar)
25Diagram 3 – Depth Control (Lock Bar) BILL OF MATERIAL INDEX P/N DESCRIPTION QTY 1 139560
26Diagram 4 – Pointer & Belt Guard
27Diagram 4 – Pointer & Belt Guard BILL OF MATERIAL INDEX P/N DESCRIPTION QTY 1 174328
28Diagram 5 – Guards & Water Distribution
29Diagram 5 – Guards & Water Distribution BILL OF MATERIAL INDEX P/N DESCRIPTION
3NOTE:NOTA:
30Diagram 6 – Blade Guard
31 Diagram 6 – Blade Guard (Rev July 11, 2002) BILL OF MATERIAL INDEX P/N DESCRIPTION
32Diagram 7 – Engine & Bladeshaft
33Diagram 7 – Engine & Bladeshaft BILL OF MATERIAL INDEX P/N DESCRIPTION
34Diagram 8 – Electric Motor
35Diagram 8 – Electric Motor BILL OF MATERIAL INDEX P/N DESCRIPTION QTY
36Diagram 9 – Air Motor
37Diagram 9 – Air Motor BILL OF MATERIAL INDEX P/N DESCRIPTION QTY 1
38Diagram 10 – Kit, Water Tank (174957) BILL OF MATERIAL INDEX P/N DESCRIPTION QTY 1
39NOTE: NOTA:
4 Symbol Definitions Definición De Simbolos• Please Read The Instructions For Use Prior To Operating The Machine For The First Time.• Antes De La Pues
22WARNINGThe engine exhaust from this productcontains chemicals known to the Stateof California to cause cancer, birthdefects or other reproductive ha
5• Do Not Use In Flammable Areas• No Usar In Áreas Inflamables• Machinery Hazard, Keep Hands And Feet Clear• Máquina Peligrosa - Mantenga Manos Y Pies
6• Repairs Are To Be Done By An Authorized Dealer Only• Las Reparaciones Deben Ser Efectuadas Únicamente Por Un Distribuidor Autorizado• Diamond Blade
7DECAL DESCRIPTIONS AND LOCATIONSDECRIPCIÓN DE CALCAMONIAS Y UBICACIONESP/N 189732Location: Front of Frame (All Models)Quantity: 1P/N 189731Location:
8NOTE:NOTA:
9Power Source Pneumatic ElectricMC 18 Model MC 18 9R MC 18 9H MC 18 13.5R MC 18 13H MC 18 5A MC 18 5EHorsepower 9 HP 9 HP 13.5 HP 13 HP 5 HP 5 HP (230
Commentaires sur ces manuels